ToolHead Free-Float, Zero-Play for Dillon XL650 / XL750


Buy 3 or more in Dillon Upgrades by Armanov and get a 5% discount in Dillon Upgrades by Armanov

What does the Free-Float, Zero-Play Toolhead do?

This toolhead has lock rings that allow the sizer and seater dies to float. This floating action allows the dies to center themselves exactly over each cartridge for the best possible alignment and more concentric ammunition.


    What is Zero Play?

    This toolhead does not use original toolhead pins supplied by dillon. This toolhed is bolted with two M3 bolts and lifts toolhead into upmost position. When you cycle cases downwards toolhead does not move and cases go out in straght line. Best practice is to loosen M3 bolts a little bit and push index shell-plate with case in to dies and tighten M3 bolts in toolhed best position.

    What is concentricity and how does it matter?

    Concentricity refers to how straight the bullet is on top of the loaded round. A bullet that is straight will enter the rifling in the barrel that way. Bullets that enter the rifling slightly crooked do not shoot with their highest accuracy.

    What’s wrong with using the OEM toolheads?

    The Dillon presses are great machines made to high quality standards. However, the cast toolheads have limitations. How do we know if the toolhead flange is flat? Or how do we know that each threaded station in the toolhead is in perfect alignment with the shellplate? How do we know that the stations are equally spaced? All of these areas compound for possible misalignments and lead to ammunition that isn’t quite as concentric as it could be. The toolhead is the final link between your dies and your press so it only makes sense that quality is extremely important. With over 100,00 EUR of dies, powder measure, and other accessories mounted in your toolhead, don’t you want to know it’s the best available!

    What is different about the new CNC Machined Toolhead?

    These toolheads are made to the highest standards. The are CNC machined from 6082 aluminum, which is much stronger and has less flex than a cast toolhead. All critical dimensions are machined in a single operation, ensuring that all surfaces are true and aligned relative to each-other. The die holes are positioned with a very high degree of accuracy and the 7/8-14 threads are machined to tight tolerances for  precise fit and alignment, yielding dies that are more precisely centered in each hole and better aligned to the cartridge cases in the shellplate. The flange is also flatter than can be achieved with a cast toolhead.

    • Made in Europe
    • Include M3 bolts and hex key.
    • Ready for Free-float rings.
    Free-float rings are sold seperately. Usually you need two free-float rings. One for resizing die and other for bullet seating die. However you can add free-float ring to each station.

    Additional information

    Weight 450 g
    Dimensions N/A
    Aluminum Colour

    Anodized Blue, Anodized Red

    Average Rating


    ( 70 Reviews )
    5 Star
    4 Star
    3 Star
    2 Star
    1 Star
    Submit your review

    70 Reviews For This Product

    1. 70

      Thomas D. (verified owner)

    2. 70

      Martin (verified owner)

    3. 70

      BONELLI FELICE (verified owner)

    4. 70

      Theodor H. (verified owner)

    5. 70

      Toni Wasescha (verified owner)

    6. 70

      Peter K. (verified owner)

      Good toolhead,gret with free float lock ring

    7. 70

      Piotr D. (verified owner)

    8. 70

      Jasmine K. (verified owner)

      It is really good and from my point of view worth the money! Sits tightly and looks good. Works well, especially with the free float lock ring!

    9. 70

      Theodor H. (verified owner)

    10. 70

      Udo M. (verified owner)

      Super Funktion, Top Qualität, sehr zu empfehlen.

    11. 70

      Udo (verified owner)

      Super Verarbeitung, Top Funktion, sehr zu empfehlen.

    12. 70

      Marc Barrois (verified owner)

      Very helpful for precision reloading

    13. 70

      Peter K. (verified owner)

    14. 70

      Joern (verified owner)

    15. 70

      Frank (verified owner)

    16. 70

      Roel (verified owner)

      Fit’s perfectly and works fine. It would be great if there were more colours available corresponding with the colours of the Dillon conversion kits.

    17. 70

      Valerij R. (verified owner)

    18. 70

      Roland Elias (verified owner)

    19. 70

      Stefan (verified owner)

      all dies will fit, except the bulletseater die from Mr. Bulletfeeder, but this Bulletseater die fits to the original Dillon Toolhead,….. so the tolerance should be not so tight.

    20. 70

      Ari Heikkila (verified owner)

    21. 70

      Jesper Bennike (verified owner)

    22. 70

      Roel (verified owner)

      No comments about the service, excellent! Toolheads fits perfectly, no free play of the toolhead.

    23. 70

      Klaus W. (verified owner)

    24. 70

      Markus (verified owner)

    25. 70

      Christian (verified owner)

      Recommandable, I would buy again…
      – Armanov service: perfect, 10/10

    26. 70

      Alarico Cammarota (verified owner)


    27. 70

      Anonymous (verified owner)

      the best toolhead ever!

    28. 70

      Anonymous (verified owner)

    29. 70

      Rafał Hinc (verified owner)

    30. 70

      Georg Gulbrandsen (verified owner)

    31. 70

      Tomasz Szydłowski (verified owner)

    32. 70

      Anonymous (verified owner)

    33. 70

      Adam Cymkiewicz (verified owner)

    34. 70

      Luca C. (verified owner)


    35. 70

      Anders Stephane Løvik (verified owner)

      a good website and professional trade. Fast delivery👍🏼

    36. 70

      Sven (verified owner)

      Nicely machined !

    37. 70

      Jouni (verified owner)

    38. 70

      Anonymous (verified owner)

      High quality and a perfect upgrade for higher accuracy loads

    39. 70

      Klaus W. (verified owner)

    40. 70

      Anonymous (verified owner)

      Return customer, that speaks for itself.

    41. 70

      Michael M. (verified owner)

      Interesting approach, good realization, good applicability

    42. 70

      Jürgen H. (verified owner)

    43. 70

      Patrik (verified owner)

    44. 70

      Henning K. (verified owner)

      Great product – easy to install

    45. 70

      Örjan Tollbom (verified owner)

    46. 70

      Anonymous (verified owner)

      Works very well.

    47. 70

      Manuel (verified owner)

    48. 70

      Tiago (verified owner)

    49. 70

      Michael M. (verified owner)

      In Verbindung mit dem Free Float Ringen eine gute Sache für große Kurzwaffenkaliber

    50. 70

      Anonymous (verified owner)

      Fits perfectly 🙂

    51. 70

      Dominik (verified owner)

    52. 70

      Anonymous (verified owner)

    53. 70

      Alexander B. (verified owner)

      Top Quality

    54. 70

      Oscar (verified owner)

    55. 70

      Klaus Bastek (verified owner)

    56. 70

      Alexander H. (verified owner)

    57. 70

      KIHL Yannick (verified owner)

    58. 70

      Alan P. (verified owner)

    59. 70

      Anonymous (verified owner)

      Fast Shipping

    60. 70

      Matteo Di Francesco (verified owner)

      Ottimo prodotto

    61. 70

      Georg S. (verified owner)

      Perfektly made ToolHead zero play and excellent finish

    62. 70

      Simon (verified owner)

    63. 70

      maurizio storaci (verified owner)

      the item is of excellent quality

    64. 70

      Simon F. (verified owner)


    65. 70

      FABIO (verified owner)

      best quality

    66. 70

      Richard Schodl (verified owner)


    67. 70

      Klaus W. (verified owner)

      Gutes Produkt, die Unterlagsscheiben sind zu klein und gehen leicht verloren. Daran sollte man arbeiten

    68. 70

      Anonymous (verified owner)

    69. 70

      Klaus W. (verified owner)

    70. 70

      gunmansk (verified owner)

      Perfect, but unfortunatelly Mr.BulletFeeder die does not fit

    Main Menu